Lunes, Setyembre 22, 2014

How to Set up a home network?





Once you know what type of network you want, and you have the necessary hardware, there are four steps you might need to take:


  1. Install any necessary hardware.
  2. Set up an Internet connection (optional).
  3. Connect the computers.
  4. Run the Set Up a Network wizard (for wireless networks only).

Each of these steps is described in detail later in this article.

Lunes, Agosto 25, 2014

SEATWORK

How to Install :

  • Memory RAM :


1.Find out what type of RAM is required for your desktop computer
2.Check how many sockets you have for RAM.
3.Browse the options
4.Make your purchase.
5.Shut down the computer
6.Open your computer case
7.Discharge any static
8.Locate your RAM sockets
9.Remove old RAM
10.Take your new RAM out of its protective packaging
11.Insert the RAM into the RAM slot.
12.Remove dust using a bottle of compressed air
13.Close up the computer
14.Power on the computer
15.Check the RAM in Windows
16.Run Memtest

  • Motherboard on your computer:


1.Open your computer case
2.Ground yourself
3.Replace the I/O panel shield
4.Find the standoffs
5.Install the standoffs
6.Place your motherboard on the standoffs
7.Install your components
8.Connect the power supply
9.Connect your front panel
10.Connect the front USB ports
11.Connect the fans
12.Install your drives
13.Install a video card


  • CPU :

1.Determine which CPU is in your computer either by reading the start-up screen or using diagnostic software.

2.Turn off and unplug the system unit.

3.Disconnect any components that may be in the way of removing the system unit's cover.

4.Remove the screws from the rear of the case and slide the cover away from the system unit case.

5.Place the cover away in a safe place.

6.Remove any and all electrical static charge from your clothes and body by touching a doorknob or any other grounded object.

7.Locate the CPU Chip

8.Check your computer's manual to see if the CPU is Proprietary before you consider upgrading to a more powerful processor

9.Remove such components as the hard drive or an expansion slot to gain full access the the chip if necessary.

10.Once the CPU is in plain view, grasp the lever on the Zero Insertion Force sockets and carefully but firmly pull the lever straight up

11.Place the beveled end of the chip to match the beveled end of the socket when inserting the new chip.

12.Confirm that the chip you buy is compatible with your system and ask if you can return the chip if there are any problems


  • Front Panel :

In order for the power button, reset button, front USB ports, front audio ports and LED lights of the computer case to work, you will need to plug their front panel connectors into the front panel header on the motherboard.
 When installing a motherboard, it's important that you know what these abbreviations stand for:
  • H.D.D LED, HD - hard drive LED
  • POWER LED, PWR LED, PLED, - power LED
  • POWER SW, PWR SW, PW - power switch
  • RESET SW, RESET, RES - reset switch
  • SPEAKER, SPEAK - internal PC speaker
  • HD AUDIO, AC' 97, F_AUDIO - front panel headphone and microphone jack
  • USB, F_USB - front panel USB port

Lunes, Agosto 18, 2014

Tools for PC Assembly


screwdriver is a tool, manual or powered, for turning screws. A typical simple screwdriver has a handle and a shaft, and a tip that 


An antistatic wrist strapESD wrist strap, or ground bracelet is an antistatic device used to safely ground a person working on very sensitive electronic equipment, to prevent the buildup of static electricity on their body, which can result in electrostatic discharge (ESD).


flashlight is a hand-held portable electrically-powered light source. Usually the light source is a small incandescent light bulb or light-emitting diode (LED).


Gas duster, also known as canned air or compressed air, is a product used for cleaning electronic equipment and other sensitive devices that cannot be cleaned using water.


cable tie or tie-wrap, also known as a hose tiezap-strapZIP TIE, is a type of fastener, for holding items together, primarily electric cables or wires.


Thermal grease  is a kind of thermally conductive (but usually electrically insulating)adhesive, which is commonly used as an interface between heat sinks and heat sources . The grease gives a mechanical strength to the bond between the heat sink and heat source, but more importantly, it eliminates air (which is a thermal insulator) from the interface area.


Needle-nose pliers are both cutting and holding pliers used by artistants jewelry designers, electricians and other tradesmen to bend, re-position and cut wire.

    


If I were a tool,I would be a flashlight.Just like a flashlight I can be the light on someones life.